Nipples

Diameter: 0.1 in - 2 in

Prevost's A2 fitting union reducers features a piece connection with a wide range of sizes in varying diameters and threads for different application requirements. It easily handles air, H2O and inert liquids. It has a pressure range ...

Diameter: 1 in

... contact area with the nozzle tip shows a surface machined to an accurate finish to prevent leakage betweennippleand nozzle tip.ZBnipplesare available in three length values to match different dimensional ...

Diameter: 1 in

HW nozzles can be assembled on a variety of differentnipples, with the same inlet, but with different lengths. The precision machinednippleinlet port assures precise positioning of the nozzle flat ...

Diameter: 17, 27 mm

ZAA/ZAB weldingnipplesallow the assembly of GX, BX or KX series nozzle tips onto pipes and spray manifolds. One end of thenippleis fixed onto the pipe and the other to the nozzle tip. ZAA is a standard ...

Diameter: 3.2 mm

Hydraulic greasenipples, straight, thread NPT, 1/8" (x 27).

Diameter: 6.4 mm

Long hydraulicnipples, 1/4" SAE. Long hydraulicnipples, M 6 x 1,00.

Hydraulic greasenipples, 45° angled, thread metric, M 10 x 1,25.

The WEH® TN1 CNG receptacle is designed specifically for car refuelling. Due to the internal aerodynamic design the TN1 CNG receptacle gives low noise (no high frequency whistle) combined with maximum flow rate and fast filling. The receptacle ...

WEH® Receptacle TN5 CNG for refueling of buses and trucks - Series The WEH® TN5 CNG receptacle is designed specifically for bus and truck refueling. Due to the internal aerodynamic design the TN5 CNG receptacle gives low noise (no high ...

Diameter: 3毫米

The WEH® TN1 H₂ 70 MPa Receptacle is designed specifically for hydrogen refueling of fuel cell electric cars with a pressure range of 70 MPa. Due to the internal aerodynamic design the receptacle gives low noise (no high frequency ...

Diameter: 0.1 in - 0.8 in

Diameter: 0.1, 0.8, 0.3, 0.4, 0.5 in

NIPPLE(TAPER) The 62.000 serie are stainless steel AISI 316L threaded adaptors. Large range of configurations:nipple、红uctions, T, L, etc. High performances in pressure (140 bar) and temperature ...

Diameter: 5 mm

The M3 male thread universal adapter infusednippleattachment is used as a connecting solution for two corresponding materials. It operates through allowing a range of angular system of linked components. A 303 stainless ...

Diameter: 7.9 mm

The MN seriesnippleattachment with M3 and M5 male threading is used to link two distinct components. It operates under 3,000 psig pressure rating. This assembly employs a comprehensive mechanism for handling imperial-threaded ...

Diameter: 0.4 in - 2 in

Pressure rates PN16 Connections solvent spigot – male thread Certificates EURASEC Hygienic Certificate, GOST Certificate, Rostehnadzor Permission

Diameter: 0.3 in - 2 in

Pressure rates - PN10 Connections - male thread Approvals - EURASEC Hygienic Certificate, GOST Certificate, Rostehnadzor Permission

Diameter: 0.4 in - 2 in

Pressure rates PN10 Connections male thread Certificates EURASEC Hygienic Certificate, GOST Certificate, Rostehnadzor Permission

Diameter: 21.8, 22 mm

These stainless steelnipplesfrom AMF ANDREAS MAIER that are used for applications that need to secure the clampingnipple. They use an adhesive to attach the clamping femalenipple...

Diameter: 0.1 in - 0.5 in

Stainless steel connections – Pure stainless steel fitting – For challenging applications Operating temperature -20°C to +150°C Materials Fittings made of stainless steel 1.4404 (AISI 316L) Seals made of FKM Thread DIN ...

Diameter: 0.5 in

Diameter: 24 mm

Diameter: 24 mm

There are many stainless steelnipplesthat are available from Temperature Technology. Thesenipplesare made from SS304 and SS316. Some of the designs that are available include the weld lips and ...

Diameter: 19, 25, 38, 31, 51 mm

Interlock-NPT-Male - AGN-NipplesWith 60°-Cone Interlock Series

Diameter: 6 mm - 25 mm

DKOL/DKOS-Nipples- Straight For Fittings with 24°-Cone DIN 2353 / DIN EN ISO 8434-1 Notes to the Assembly: It is very important to lubricate the insert thread before screwing into the ferrule. (Lubricants Category 12) O-Ring = NBR

Diameter: 6 mm - 30 mm

With O-ring Sealing - NBR On request: FPM Matching Type 24°-Inside Tapers Bore Type W DIN 3861

Diameter: 0.1 in - 4 in

ISIFLO gjengefittings er gjengete rørdeler for sammenføyning med hamp, gjengetape eller tilsvarende hvor også flytende tetting også kan benyttes. Finnes i dimensjoner fra 1/8” opp til 4” ISIFLO gjengefittings produseres i avsinkningsbestandig ...

Diameter: 0.8 in - 3 in

ISIFLO螺纹管件螺纹pipe fittings for use with hemp, thread tape or threat paste. Available in dimensions from 1/8 "up to 4" ISIFLO thread fittings are produced in dezincification-resistant brass. Ordinary pipe ...

Diameter: 20 mm - 63 mm

Our brass products are made in RA455 (CW625N) which is a special dezincification resistant brass (DZR). Our brass alloy undergoes a hot forging where the brass becomes a mixture of alpha and beta grains. Beta grains contain a slightly ...

Diameter: 50 mm

Diameter: 0.5, 0.8, 1 in

Description NiroTherm Threaded adaptor, male/male thread

Diameter: 0.5 in - 4 in

Connection of two identical female threaded connections RS - twinnippleshave the same male threads on both sides and, as a rule, a wrench flat for wrenches and/or adjustable hook wrenches. Features: Quick connection ...

Diameter: 0.5 in - 6 in

... Male thread for welding Threaded weldednippleshave a male thread on one side and a weld end on the other side. To create a connection on the plant or tank for male threads, you need a threaded weldednipple. ...

Diameter: 15 mm - 150 mm

Connection of flanged and female threaded connections RS - screw flangenipplehave a fixed flange on one side and a male thread on the other. They connect a flanged connection with a female thread. The male thread ...

Diameter: 0.1, 0.3, 0.4, 0.5 in

Nipplemale male conical thread nickel plated brass Body material: Nickel-plated Brass

Diameter: 0.8, 0.5, 0.3 in

SM SériésNipples(hydraulic) up to 6000 psi connect with SM Sériés Couplers. Parker's SM Sériés are double shut-off quick couplings with manual sleeves and poppet valves. Female port end options include NPTF, O-ring ...

Diameter: 0.1 in - 1 in

1/8, 1/4, 3/8, 1/2, 3/4 and 1 in. (6, 8, 10, 15, 20 and 25mm) Description: Ideal for use with copper, brass, iron pipe on oil, natural gas, water and air lines.

Diameter: 100 mm

ISO THREADED UNIONS WELDINGNIPPLESSTAINLESS STEEL 316L WELDINGNIPPLES

Diameter: 17 mm - 22 mm

... Screw-to-connect pressure testing The pressure testingnipplesare designed to work with most fittings available (ISO 15171-2) and offer a leakage-free solution, even when using low viscosity fluids. Our testnipples...

- Whitworth pipe thread, thread M5 - With inner cone according to DIN EN 560 - Chambered O-rings FPM - Material stainless steel 1.4301 / 1.4307 - Temperature range -20 to +120 ˚C - Pressure range -0.95 to 16 bar

Diameter: 0.5 in - 4 in

Series of fittings designed for conveying fluids under pressure with a threaded jointing system Nominal pressure: PN 16 Standards: EN ISO 1452, EN ISO 15493, ISO 228-1

SKU : 486 - OIL FILTERNIPPLEINSTALLER - SERIES 60 DETROIT DIESEL ENGINES PRODUCT DESCRIPTION - Used to reinstall or tighten the oil filternippleinto the oil filter housing. - 2" six-point hex ...

Diameter: 0.1 in - 1 in

HexNipplesare appreciated for their excellent functioning, corrosion resistance and long lasting properties. The offerednipplesare designed to withhold varying flow pressures and form an important ...